Parameters for SetParm() and GetParm(). Defaults in parenthesis.
| Member Name | Description |
|---|---|
| DXBD_FLASHCHR | Flash character - character that causes a hook flash when detected. (ampersand) |
| DXBD_INITDLY | Initialization delay. |
| DXBD_MINPDON | Minimum Pulse detection On (2) |
| DXBD_MINPDOFF | Minimum Pulse Detection off (2) |
| DXBD_TTDATA | DTMF length (duration) for dialing. (10) |
| DXBD_MINSLON | Minimum Silence On (1) |
| DXBD_MINSLOFF | Minimum Silence off (1) |
| DXBD_MINTION | Minimum DTI On (5) |
| DXBD_MINTIOFF | Minimum DTI off (5) |
| DXBD_R_EDGE | Ring Edge - (ET_ROFF - end of ring) |
| DXBD_FLASHTM | Flash time - length of time onhook during flash (50) |
| DXBD_PAUSETM | Pause time (200) |
| DXBD_MINOFFHKTM | Minimum Offhook time (10ms) (250) |
| DXBD_P_MK | Pulse Dial Make (4) |
| DXBD_P_BK | Pulse Dial Break (6) |
| DXBD_P_IDD | Pulse Interdigit delay (100) |
| DXBD_T_IDD | DTMF Interdigit delay (time between digits in DTMF dialing) (10) |
| DXBD_OFFHDLY | Offhook Delay (50) |
| DXBD_R_ON | Ring-on Interval (100ms) (3) |
| DXBD_R_OFF | Ring-off interval (100ms) (5) |
| DXBD_R_IRD | Inter-ring Delay (100ms units) (80) |
| DXBD_S_BNC | Silence and nonsilence debounce (4) |
| DXBD_MINIPD | Minimum Loop Interpulse Detection (25) |
| DXBD_MINLCOFF | Minimum Loop current off (0) |
| DXBD_MAXPDOFF | Maximum Pulse digit off - max time loop current may be off before existing loop pulse digit is considered invalid and reception is reinitialized. (50) |
| DXBD_MINISL | Minimum Interdigit Silence (25) |
| DXBD_MAXSLOFF | Maximum Silence off - maximum time for silens being off during audio pulse detection (25) |
| DXBD_HWTYPE | Hardware type D/40 D/41, D.xxxSC etc. |
| DXBD_CHNUM | Number of channels on the board |
| DXBD_SYSCFG | System configuration |
| DXBD_MFMINON | Minimum MF on (10ms units) (0) |
| DXBD_MFTONE | MF Minimum Tone duration (10ms units) (6) |
| DXBD_MFDELAY | MF Interdigit delay (10ms units) (6) |
| DXBD_MFLKPTONE | MF length of LKP Tone (10ms units) (6) |
| DXBD_TEMPLATE | Set the dialing qualification template. Pass in the Silence Threshhold (i.e. 250) |
| DXCH_DTMFTLK | Sets the minimum time for DTMF to be present during playback to be considered valid. (5) |
| DXCH_DTMFDEB | DTMF debounce time. |
| DXCH_DTINITSET | Specifies which DTMF digits to initiate play on |
| DXCH_WINKDLY | Wink delay (15) |
| DXCH_WINKLEN | Wink Length (15) |
| DXCH_MINRWINK | Minimum Loop current for Wink (10ms units) (10) |
| DXCH_MAXRWINK | Maximum Loop Current for Wink (10ms units) (20) |
| DXCH_TTDATA | DTMF length for dialing. (10) |
| DXCH_T_IDD | Dtmf interdigit delay (5) |
| DXCH_ADSIALERT_LENGTH | |
| DXCH_ADSIALERT_ACK | |
| DXCH_ADSIACK_LENGTH | |
| DXCH_ADSIACK_FSK | |
| DXCH_ADSIALERT_AMPL | |
| DXCH_MFMODE | Selects the minimum length of KP tones to be detected (2) |
| DXCH_MFDIAG | |
| DXCH_PLAYDRATE | Play Digitization Rate - (6000) |
| DXCH_RECRDRATE | Record Digitization Rate (6000) |
| DXCH_DFLAGS | DTMF detection edge select |
| DXCH_RINGCNT | Number of rings to wait before returning a ring event (4) |
| DXCH_CALLID | Enable or disable Caller ID for the channel. (disable) |
| DXCH_AUDIOLINEIN | Enable or disable the Proline/2V audio jack line-in on voice channel 2 |
| DXCH_DIGBUFMODE | |
| DXCH_XFERBUFSIZE | Library buffer size (512) |
| DXCH_RXDATABUFSIZE | DXCH_RXDATABUFSIZE |
| DXCH_TXDATABUFSIZE | DXCH_TXDATABUFSIZE |
| DXCH_NUMRXBUFFERS | DXCH_NUMRXBUFFERS |
| DXCH_NUMTXBUFFERS | DXCH_NUMTXBUFFERS |
| DXCH_VARNUMBUFFERS | DXCH_VARNUMBUFFERS |
| DTG_MINPDON | Minimum pulse dial reception on. |
| DTG_MINPDOFF | Minimum pulse dial reception off. |
| DTG_MAXPDOFF | Maximum interdigit reception delay. |
| DTG_MINIPD | Maximum pulse digit reception off. |
| DTG_P_MK | Send pulse make time. |
| DTG_P_BK | Send pulse break time. |
| DTG_P_IDD | Send pulse interdigit delay. |
| DTG_PDDLFTIM | Flash time. |
| DTG_PDFLASH | Flash character. |
| DTG_CABTYPE | Cable type (LIU). |
| DTG_OOFMAX | Out of frame errors, maximum less than or =15). |
| DTG_FECRMAX | Max FECR error count less than or=255) |
| DTG_ESECMAX | Extended superframe Err. cnt max less than or=15. |
| DTG_FECSMAX | Frame error count saturation. |
| DTG_BPVCMAX | Bipolar violation count max less than or=255. |
| DTG_RDEBON | Receive debounce on value, in 10ms units. |
| DTG_RDEBOFF | Receive debounce off value,in 10ms units. |
| DTG_PCDEAD | Signalling dead parameter. |
| DTG_RCVTOL | Low word of rcv timeout (and ack). |
| DTG_RCVTOH | Hi byte of 3 byte rcv and ack timeout. |
| DTG_CODESUPR | Suppression value (b8zs,bit7 or tran) |
| DTG_WINKMAX | Wink time, in 10ms units. |
| DTG_REDTIME | RLOS -> red alarm transition time. |
| DTG_RCOVRTM | Red alarm recovery time. |
| DTG_PDPSTIM | Pulse dialing pause time |
| DTG_WINKMIN | Wink time, in 10ms units. |
| DTG_WINKLEN | Wink length(xmt), in 10ms units. |
| DTG_PREWINK | Pre-wink delay in 10ms units. |
| DTG_CRCENABL | CRC4 switch (ENABLE or DISABLE) |
| DTG_CECRMAX | Max CRC4 error count less than or= 255. |
| DTG_ECRRSTTM | Err cnt register reset time in 100ms unts |
| DTG_RXTXIDLE | Receive and Trnsmit idle patterns |
| DTG_SEIZESIG | Line Seizure and Response |
| DTG_DVPRMMAX | Max value of device parameter |
| DTG_SETCLK | Set the clock source. |
| DTG_SETBDMD | Set the mode. |
| DTG_IDLTYP | Set the idle type. |
| DTG_DSERRC | Disable error condition mask |
| DTG_ENERRC | Enable the error condition mask. |
Namespace: CTI32NetLib
Assembly: CTI32NetLib (in CTI32NetLib.dll)